X :w/in OPTIONS FIELD, DENOTES NO OPTION SELECTED 4. : Wire Enclosure Panels (factory): Louvered Enclosure Panels (factory): Acoustic Sound Blanket: Ultra Low Sound Fans: 1" Deflection: Seismic: Neoprene Pads
#York ycal 0043 code#
Switch: ASME Pressure Vessel Code : Remote DX Cooler : 300 PSIG DWP Waterside: Double Thick Insulation: Weld Flange Kit: Victaulic Flange Kit: One Flow Switch: Two Flow Switch: Three Flow Switch: One Diff. : 1st Year Parts Only: 1st Year Parts & Labor: 2nd Year Parts Only: 2nd Year Parts & Labor: 5 Year Compressor Parts Only: 5 Year Compressor Parts & Labor Only: 5 Year Units Parts Only: 5 Year Unit Parts & Labor : Aluminum: Copper: Black Fin: Phenolic: TEAO Fan MotorsĮVAP. Y # E E 1 7 E C 2 8 A 4 0 B L 4 6 5 0 5 8 X UnIt nOMenClatURe naMePlate enGIneeRInG Dataġ 2 3 4 5 6 7 8 9 10 11 12 13 14 15BASE PRODUCT TYPE NOMINAL CAPACITY UNIT DESIGNATOR REFRIGERANT VOLTAGE/STARTER DESIGN/DEVELOPMENT LEVEL 62Table 33 - RECOMMENDED SPARE PARTS - YCAL STYLE 'E' CHILLERS. 62Table 32 - REMOTE TEMPERATURE RESET KIT COMPONENTS. 60Table 30 - OPTIVIEW REMOTE CONTROL CENTER PARTS. 59Table 28 - FIELD INSTALLED OPTIONS KIT NUMBERS. 58Table 27 - VIBRATION ISOLATORS PART NUMBERS. 52Table 19 - TEMPERATURE SENSORS AND TRANSDUCERS.53Table 20 - TRANSDUCER AND THERMISTOR WIRE HARNESS CONNECTORS - FIELD REPLACEMENT PARTS.
33Table 16 - CONTROL AND POWER PANEL COMPONENTS. 31Table 15 - CONTROL PANEL AND POWER PANEL IDENTIFIERS. 29Table 14 - OPTION PANEL AND POWER PANEL CONFIGURATIONS. 27Table 12 - R-410A COMPRESSOR PART NUMBERS.27Table 13 - COMPRESSOR HEATER AND COMPRESSOR SOUND BLANKET PART NUMBERS. 18Table 10 - REFRIGERANT PIPING COMPONENTS. 16Table 8 - FAN COMPONENTS - MODELS YCAL0019 and YCAL0022. 10Table 5 - ALFA LAVAL HEAT EXCHANGER AND RELATED COMPONENTS. 9Table 4 - SWEP HEAT EXCHANGER AND TXV PARTS (STANDARD AND DOUBLE INSULATION) YCAL0043 - YCAL0066. 7Table 3 - SWEP HEAT EXCHANGER PARTS (STANDARD AND DOUBLE INSULATION) YCAL0019 - YCAL0033. 5Table 2 - SWEP HEAT EXCHANGER - DOUBLE INSULATION. TaBle OF COntentsTable 1 - SWEP HEAT EXCHANGER - STANDARD INSULATION. May result if personnel fail to observe safety precautions. Is used in the operation of this equipment.DeatH OR seRIOUs InJURY LOw VOltaGeDO NOT be misled by the term “low voltage.” Voltages as low as 50 volts may cause death. When working inside equipment with power off, take care to discharge every capacitor likely to hold dangerous potential.īe careful not to contact high voltage connections when installing or operating this equipment.
Shut off power supply to the equipment before beginning work and follow lockout procedures. Work on electronic equipment should not be undertaken unless the individual(s) have been trained in the proper maintenance of equipment and is (are) familiar with its potential hazards. If there is any question in the mind of operating/ service personnel as to the applicability of these documents, then, prior to working on the equip-ment, they should verify with the owner, whether the equipment has been modified and if the current litera-ture is available. It is the responsibility of operating/service personnel as to the applicability of these documents to the equip-ment in question.
#York ycal 0043 update#
While Johnson Controls makes no commitment to update or provide current information automatically to the manu-al user, that information, if applicable, can be obtained by contacting the nearest Johnson Controls Engineered Systems Service office. In complying with Johnson Controls policy for con-tinuous improvement, the information contained in this document is subjected to change without notice.
0 kommentar(er)
